24mm MD

Discussions for scratch builders. For the enthusiast that builds from the ground up. Tell us what you've built and what projects you working on in the space race.

Moderator: Moderators

Lister
Engineer
Engineer
Posts: 967
Joined: Fri Jun 05, 2015 5:36 pm
Location: Bendigo, Victoria

Re: 24mm MD

Postby Lister » Wed Jun 08, 2016 5:02 pm

Using an easy mini or eggtimer quark altimeter and the GPS tracker that I made from Vances design. It will be tight but I'll get it in there.

User avatar
SpaceManMat
Astronaut
Astronaut
Posts: 1889
Joined: Mon Dec 15, 2008 9:56 pm
Location: Brisbane

Re: 24mm MD

Postby SpaceManMat » Wed Jun 08, 2016 5:11 pm

Lister wrote:Using an easy mini or eggtimer quark altimeter and the GPS tracker that I made from Vances design. It will be tight but I'll get it in there.


Just saw Vance's tracker, will be interesting to see this.
QRS: 124
AMRS: 32 L2 RSO
Highest Altitude: 10,849 feet
Largest Motor: CTI 1115J530 IM
Current Project: X Wing

Lister
Engineer
Engineer
Posts: 967
Joined: Fri Jun 05, 2015 5:36 pm
Location: Bendigo, Victoria

Re: 24mm MD

Postby Lister » Wed Jun 08, 2016 5:38 pm

I willl upload a photo of the avbay when its all done and will post the data and outcome of the test flights.

Lister
Engineer
Engineer
Posts: 967
Joined: Fri Jun 05, 2015 5:36 pm
Location: Bendigo, Victoria

Re: 24mm MD

Postby Lister » Sat Jun 11, 2016 6:15 pm

New tip for the MD24 nose cone. Weighs about 10 grams which is exactly the weight I needed to put at the tip. Not bad for chucking it up in the drill (AKA the Vance Lathe) and grinding to shape with the angle grinder and some flat files

2016-06-11 18.09.27.jpg
2016-06-11 18.09.27.jpg (130.78 KiB) Viewed 852 times

Lister
Engineer
Engineer
Posts: 967
Joined: Fri Jun 05, 2015 5:36 pm
Location: Bendigo, Victoria

Re: 24mm MD

Postby Lister » Tue Jun 14, 2016 8:54 pm

Here is the finished nose cone. The tip is epoxied in place, the bulkplate/end cap has a hole in it that locks down with a nut and a small bit of a U bolt with the thread poking out the base of the shoulder.
2016-06-14 20.42.02.jpg
2016-06-14 20.42.02.jpg (133.08 KiB) Viewed 837 times


I need to make a thin sled for the AV bay or zip tie the Atlus Metrum easy mini and the 915mhz 3DR radio together and then have the batteries bellow, I have some 1mm CF from hobby king that I would normally use but with the radio and GPS I wasnt sure if it would be a good idea :?: if someone can give me a yes or no that would be a great help. Other than that its done. Just going to make a new base for the launch tower and its good to launch this Sunday weather permitting.
2016-06-14 20.54.00.jpg
2016-06-14 20.54.00.jpg (155.09 KiB) Viewed 837 times

vance2loud
Rocket Crew
Rocket Crew
Posts: 276
Joined: Wed May 14, 2014 12:44 pm
Location: Devonport, Tasmania

Re: 24mm MD

Postby vance2loud » Tue Jun 14, 2016 9:08 pm

If you could put the altimeter on one side of the carbon and the radio on the other it will help make sure that the radio can't interfere with the altimeter.
In theory they shouldn't anyway but a bit of shielding between them wouldn't hurt
TRA #15165 AMRS #50
I do it because i can, I can because I want to, I want to because you said I couldn't. - Unknown
I have not failed. I've just found 10,000 ways that won't work.
- Thomas Alva Edison

Lister
Engineer
Engineer
Posts: 967
Joined: Fri Jun 05, 2015 5:36 pm
Location: Bendigo, Victoria

Re: 24mm MD

Postby Lister » Tue Jun 14, 2016 9:09 pm

Would a metal washer work as a shield?

vance2loud
Rocket Crew
Rocket Crew
Posts: 276
Joined: Wed May 14, 2014 12:44 pm
Location: Devonport, Tasmania

Re: 24mm MD

Postby vance2loud » Tue Jun 14, 2016 9:16 pm

a metal bulkhead with the antenna connector poking through it should work as a ground plane increasing the effectiveness of the antenna. Ideally for 915MHz it should be a lot larger but anything should be better than nothing.
Even gluing a layer of aluminium foil to a bulkhead should in theory increase shielding and performance from the radio
TRA #15165 AMRS #50
I do it because i can, I can because I want to, I want to because you said I couldn't. - Unknown
I have not failed. I've just found 10,000 ways that won't work.
- Thomas Alva Edison

Lister
Engineer
Engineer
Posts: 967
Joined: Fri Jun 05, 2015 5:36 pm
Location: Bendigo, Victoria

Re: 24mm MD

Postby Lister » Tue Jun 14, 2016 9:34 pm

Cool, I'll have a play around with it once the sled is done and see what I can come up with.. it wont be pretty, but it will work :)

Lister
Engineer
Engineer
Posts: 967
Joined: Fri Jun 05, 2015 5:36 pm
Location: Bendigo, Victoria

Re: 24mm MD

Postby Lister » Wed Jun 15, 2016 5:04 pm

One of the MD24 rockets ready for this weekend.
2016-06-15 16.59.53.jpg
2016-06-15 16.59.53.jpg (132.43 KiB) Viewed 814 times


Also got the new launch tower made that has a bit more room and will also take a MD29, just need to WD40 the rods, install a couple of bits of aluminium as blast deflectors and its good to go for this coming Sundays launch :D
2016-06-15 17.00.29.jpg
2016-06-15 17.00.29.jpg (120.98 KiB) Viewed 814 times

Lister
Engineer
Engineer
Posts: 967
Joined: Fri Jun 05, 2015 5:36 pm
Location: Bendigo, Victoria

Re: 24mm MD

Postby Lister » Wed Jun 15, 2016 7:49 pm

MD24 & MD29 launch tower from the top with the blast deflector installed :)
Attachments
2016-06-15 19.46.52.jpg
2016-06-15 19.46.52.jpg (132.57 KiB) Viewed 801 times


Return to “Scratch Built”

Who is online

Users browsing this forum: Bing [Bot] and 1 guest