Modular Rocket

Discussions for scratch builders. For the enthusiast that builds from the ground up. Tell us what you've built and what projects you working on in the space race.

Moderator: Moderators

Jim-K
Rocket Onlooker
Rocket Onlooker
Posts: 3
Joined: Mon Nov 04, 2019 9:53 pm

Modular Rocket

Postby Jim-K » Sat Nov 16, 2019 12:08 am

With the summer warming up and no flying until April/May, I have started to tinker with a modular rocket design. My aim is to make different sections that can be stuck together to mix and match different motors, recovery, staging etc.

So far, I have 3D printed some ends and tried our a few prototype sections. It all seems to work, but once I set forth with a particular interface, its going to be hard to change. Happy to listen to opinions on features to add or remove.

The basic structure is based upon BT-70 & 80 tubes. This gives plenty of room to fit stuff into the airframe later. 3D printed ends are bonded in with some balsa stringers running longitudinally and a bit of PU foam.

Here are some illustrations:

4710C058-C921-4B47-BCDA-FD6615A9BCCE.jpeg

A53B007C-C347-4CB4-977B-D64605BDF540.jpeg


I built a short section - about 120mm long - to check the longitudinal strength. About 2kN, which should be sufficient for anything I am likely to put in the back end.

2F856838-D77A-4445-BFAE-5EA7B160CB60.jpeg


The features so far are:
- Each section joined by 6 off M1.6 fasteners.
- Four pairs of balsa stringers to assist with longitudinal load.
- Two longitudinal tubes to assist with running communications.
- Radial hard points. Initially closed, but can be fitted with an M2 ‘helicoil’ as necessary.

First up I will build a tail section, a mid section with parachute and a nose section. Fly it with a 24 mm diameter E or F category, and see how we go.

316C85F5-AD01-497A-9B8B-11DD85DB0C4A.jpeg
316C85F5-AD01-497A-9B8B-11DD85DB0C4A.jpeg (22.88 KiB) Viewed 788 times


Ideally there will be time for bigger, faster, higher etc later.

User avatar
SpaceManMat
Astronaut
Astronaut
Posts: 2220
Joined: Mon Dec 15, 2008 9:56 pm
Location: Brisbane

Re: Modular Rocket

Postby SpaceManMat » Sat Nov 16, 2019 7:48 am

Neat idea. It will be interesting to see how this comes together.
QRS: 124
AMRS: 32 L2 RSO
Highest Altitude: 13,647 feet
Fastest Flight: Mach 1.55
Largest Motor: CTI 1115J530 IM
Current Project: X Wing

strud
Engineer
Engineer
Posts: 984
Joined: Thu Oct 02, 2008 7:37 am
Location: Central Tablelands, NSW

Re: Modular Rocket

Postby strud » Sat Nov 16, 2019 11:54 am

I like modular approaches, reuse saves time and reduces risk in new projects.... theoretically.

M1.6 fasteners, wow didn't know they existed!

Jim-K
Rocket Onlooker
Rocket Onlooker
Posts: 3
Joined: Mon Nov 04, 2019 9:53 pm

Re: Modular Rocket

Postby Jim-K » Wed Jan 08, 2020 11:34 pm

Starting at the top for no particular reason, I have a nose cone assembly.

This assembly is just going to pop off the top with the ejection charge on the end of the motor. The typical nose cone (this one was from Apogee) will do this without modification, but the inner BT-70 does not suit the BT-80 nose cone. I also have plans to use the same nose cone with more sophisticated rockets later. I also just like tinkering.

The 3D printed rings (from 3D Hubs in FDM PLA) came out slightly 'woolly', but the tolerances seem good and they slip together with the tubes neatly. First off, I have bonded in the washers and nuts. This seemed to work best if the joint is torqued up gently so that the nuts and washers are compressed into the rings, though clearly you need to be careful with the epoxy adhesive.

Nut End Ring.JPG
Nut End Ring.JPG (87.47 KiB) Viewed 175 times


Bolt End Ring.JPG
Bolt End Ring.JPG (86.04 KiB) Viewed 175 times


Next I bonded on the BT-70 and 80 tubes (these are identical lengths) followed by the balsa stringers. I also trimmed out the sides to allow access to the bolts, though I could probably have done this later.

Short Section - Unbonded.JPG


Sticking the two parts together was trickier and time bounded with the PU foam and epoxy curing before my eyes. I will try to get some photos next time. The epoxy went on the end rings. The PU foam in between the two balsa stringers (in the trial parts, the PU foamed up and bonded the inner and outer tubes together).

Short Section - Bonded.JPG
Short Section - Bonded.JPG (47.26 KiB) Viewed 175 times


The nose cone has a similar structure with a BT-70 running about 50% of its length. It also has 1/8 inch aluminum tubes running to the end of the BT-70 to allow communications for later systems. But I didn't take any photographs.

Nose Cone.JPG


The next post will be about the central section. This will contain the parachute, maybe some other things. I might also think about painting the external surface.

User avatar
SpaceManMat
Astronaut
Astronaut
Posts: 2220
Joined: Mon Dec 15, 2008 9:56 pm
Location: Brisbane

Re: Modular Rocket

Postby SpaceManMat » Thu Jan 09, 2020 11:50 am

Looks pretty nice. Kind of wish I had added a place to put nuts in the cockpit for my X Wing, but I didn't because I wanted to make sure it never fell out because there will be no access to the underside.
QRS: 124
AMRS: 32 L2 RSO
Highest Altitude: 13,647 feet
Fastest Flight: Mach 1.55
Largest Motor: CTI 1115J530 IM
Current Project: X Wing


Return to “Scratch Built”

Who is online

Users browsing this forum: No registered users and 6 guests